NA Graphics
View Cart
     

Bindery

We carry a selection of equipment for folding, paper drilling, and pad making. Our three padding presses provide a range of capabilities from hobby to commercial use. A bone folder is a must for folding signatures and cards. The XCEL Paper Drill Bit Sharpening Kit can keep your paper drill bits, and you, efficient.

We can furnish wood drill blocks for the following product lines: Challenge, Baum, Nygren Dahly, Lassco, Spinnet, Lawson, Seybold, Rosback, Sterling, Iram, Martin Yale, Lihit and cutting boards for the Challenge Three Knife Trimmer. We can supply virtually any size required in any quantity from one dozen on up. Call for your particular needs, or see list of Drill Blocks at bottom of page.

 
products/thumbs/bonefolder_thumb.jpg "Bone Folder, 8 inch, rounded ends"
$8.75
BF11
See end of this section for bone folders with pointed ends.
Quantity   
 
products/thumbs/xcelsharp_thumb.jpg "XCEL Paper Drill Bit Sharpener Kit, with diamond coated deburring tool and lubricating stick"
$129.00
BG-XCEL Quantity   
 
Drilla "#305 Hollo Paper Drill Bits, Style A, B, C"
$23.95
SU305-1

Per each in quantities of 1 to 5. Illustration shows Style A for Challenge, Super Speed, and Ottowa Paper Drills.

Our Hollo Drills are manufactured with a special alloy of the finest steels: chromium, vanadium, and molybdenum. They resist wear, stay sharp longer, and won't clog, chip, or twist. The razor sharp cutting edges are carefully machined to precise tolerances. Every Hollo Drill is thoroughly inspected before it leaves the factory. Our paper drills are guaranteed against breakage with normal use.


Quantity   
 
Drillb "#305 Hollo Drill Bits, Style A, B, C, quantities of 6 and up"
$23.25
SU305-10
Illustration shows Style B for Lawson, Seybold, Wright, and Rosback Paper Drills.
Quantity   
 
Drillc "#305 Hollo Drill Bit Style D"
$26.95
SU305-11
Illustration shows Style C for Nygren-Dahly Paper Drills. Sizes available are 1/2", 1/4", 1/8", 3/16", 3/8", 5/16", and 7/16". Please specify on check out page under Special Instructions.
Quantity   
 
Drilld "#305 Hollo Drill Bit Style D in quantities of 6 and up"
$26.25
SU305-12
Illustration shows Style D for Chandler & Price and Pioneer Paper Drills.
Quantity   
 
"Thermographic powder, in Extra Fine or Fine, clear gloss finish, per pound"
$18.76
TG100
Please specify extra fine (for small type) or fine. We can supply the powder in any quantity, typically in 25 lb cartons for volume users. Other colors and finishes available, subject to minimum order size.
Quantity   
 
"Fingertip Moistener"
$1.75
FM10050
Fingertip moistener in convenient 3/8 oz plastic container, non-toxic, long lasting, stainless, ideal for hand feeding and sorting paper. Brand name "Sortkwik."
Quantity   
 
ClampPad "Blue Lightning Clamp Pad"
$33.00
CP101
Box of 2 pads, each 3" x 15" Reduces paper cutter clamp marks on paper and carbonless stock. Prevents crushing the spine of books during clamping. The Blue Lightning Cutter Pad is made from a long lasting high density polyurethane which is permanently attached to a magnetic backing. Simply place the magnetic cutter pad under the clamp of your cutter. The strong magnet holds the pad tightly in place while the foam surface provides a nice even pressure on the stock. Made in the U.S.A.
Quantity   
 
LasscoRoundCorner "Lassco Wizer Desktop Corner Rounder"
$174.00
CR-20
Model CR-20 is a handy table top round corner machine that has been a favorite tool used by printers for well over a half century. Machine is hand operated and will cut small lifts of both paper and plastic. One standard cutting blade of your choice included with machine. Standard size radius are 1/8", 1/4", 3/8", 1/2". Additional standard cutting blades are priced at $99.00 each and are a special order. Special size radius cutting units are 1/16", 3/32", 5/32", 3/16", 3/16", and 5/8" radius and are priced at $139.00 each, special order.
Quantity   
 
BoneFolderPointed "Bone Folder, Pointed End"
$7.50
BF12
Folding Bones are made from genuine bleached bone. Perfect for hand folding large sheets of paper or hand scoring cover stock. Available in 8" lengths, either pointed one end or rounded both ends. Not made from endangered species or ivory.
Quantity   
 
JoggerBlock2 "Jogger Block 4"x10" with magnetic strip"
$52.50
MA312
Jogger blocks are used with paper cutters and provide a significant measure of safety when cutting paper. The block is pushed against the front edge of the paper being cut, a magnetic strip in the bottom of the block holds it in place, and then the cutter is run through its cycle. The block holds the cut edge of paper from falling over, especially useful when the cut off portion needs to cut again. Other sizes are available.


Quantity   
 
"Creasing Matrix, Mauve, 30 inches long per 16 strips"
$51.25
SR520M
Mauve is recommended for scoring Crane's Lettra 110#.
Quantity   
 
Drillblock "Challenge Drill Blocks, round 1 1/2" x 3/4" thick, per dozen"
$7.50
CDB 1

Round wood, per dozen, end grain


Quantity   
 
"Baum, Nygren-Dahly, 18" x 1 1/4" x 3/8""
$51.75
BDB14
Oblong, wood, grain long, per 3 dozen
Quantity   
 
"Baum, Nygren-Dahly, 1 3/8" x 3/4""
$7.50
BDB10
Round, wood, end grain, per 1 dozen
Quantity   
 
"Baum, Nygren-Dahly, 24" x 1 1/4" x 3/8""
$69.25
BDB15
Oblong, wood, long grain, per 3 dozen
Quantity   
 
"Baum, Nygren-Dahly, 6 1/2" x 1 1/4" x 3/8""
$23.75
BDB11
Oblong, wood, grain long, per 3 dozen
Quantity   
 
"Baum, Nygren_Dahly, 18" x 1 1/4" x 5/16""
$51.75
BDB13
Oblong, wood, grain long, per 2 dozen
Quantity   
 
"Baum-Nygren-Dahly, 6 1/2" x 1 1/4" x 5/16""
$23.75
BDB 12
Oblong, wood, grain long, per 3 dozen
Quantity   
 
"Challenge Drill Blocks, 1 7/8" x 7/16" (Climax)"
$13.25
CDB2
Round, wood, end grain, per dozen
Quantity   
 
"Challenge Drill Blocks, 12" x 1 1/4" x 3/8""
$34.75
CDB6
Oblong, wood, long grain, per 3 dozen
Quantity   
 
"Challenge Drill Blocks, 2 1/2" x 3/4""
$13.25
CDB-13
Round, wood, end grain, per dozen
Quantity   
 
"Challenge Drill Blocks, 2" x 6" x 1/8" for Jumbo Drill"
$1.70
CDB9
Oblong, Plastic, per each
Quantity   
 
"Challenge Drill Blocks, 24" x 1 1/4" x 3/8""
$69.25
CDB8
Oblong, wood, long grain, per 3 dozen
Quantity   
 
"Challenge Drill Blocks, 3" x 3/4""
$17.25
CDB4
Round, wood, end grain, per dozen
Quantity   
 
"Challenge Drill Blocks, 6" x 1 1/4" x 3/8""
$23.75
CDB 5
Oblong, wood, long grain, per 3 dozen
Quantity   
 
"Challenge Drill Bocks, 18" x 1 1/4" x 3/8""
$51.75
CDB7
Oblong, wood, long grain, per 3 dozen
Quantity   
 
"Lassco, Spinnit, 2 7/16" x 5/8" with hole"
$15.50
LAS1
Round, wood, end grain, per 1 dozen
Quantity   
 
"Lawson, Seybold 12 1/2" x 1 1/8" x 3/8""
$30.75
LS18
Oblong, wood, long grain, per 3 dozen
Quantity   
 
"Lawson, Seybold 24" x 1 1/8" x 3/8""
$69.00
LS19
Oblong, wood, long grain, per 3 dozen
Quantity   
 
"Lawson, Seybold 8 5/8" x 1 1/8" x 3/8""
$24.25
LS17
Oblong, wood, long grain, per 3 dozen
Quantity   
 
"Martin Yale, Lihit, 11 3/4" x 1x" x 1/8""
$11.25
MY22
Oblong, plastic, per 1 dozen
Quantity   
 
"Martin Yale, Lihit, 11 3/4" x 2 3/8" x 1/8""
$16.50
MY23
Oblong, plastic, per 1 dozen
Quantity   
 
"Rosback 1 1/2" x 3/8""
$7.50
ROS20
Round, wood, end grain, per 1 dozen
Quantity   
 
"Sterling, Iram Drill Block 10" x 1" x 3/16""
$12.95
SI21
Oblong, plastic, per 1 dozen
Quantity   
 
"Rosback Perforating Pin"
$0.85
RP-100
Replacement pins for Rosback pin perforators. Size .0395 x 13/16 with formed head on non-punching end. These are custom made by Rosback for NA Graphics for their line of flat table round hole pin perforators going back to the 19th century and manufactured at least into the 1950s, perhaps later. Price per each, in a minimum order for 10 pins.
Quantity